Hot water design is one of the most important parts of a heat pump installation.

A lot of people think hot water design is simply about fitting a cylinder that is big enough for the number of people in the house. That is part of it, but it is not the full story.

Older rules of thumb often worked from a simple litres-per-person allowance. Modern hot water design needs to go further than that. It should look at how the household actually uses hot water, what temperature the water is stored at, how often the cylinder reheats, where the cylinder is located, and what works best for the customer day to day.

At 11 Kings View, the hot water design was one of the most important parts of the project.

Start With the People in the Home

The first question is simple: how many people live in the house?

But after that, we need to understand how they use hot water.

Do they shower every day?
How long are the showers?
Do several people shower one after another?
How often do they have baths?
Do they wash up by hand?
Do they use a dishwasher?
Do they need lots of hot water in the morning, in the evening, or spread across the day?

Two homes with the same number of people can have very different hot water needs.

A family that has long showers and regular baths will need a different setup to a family that has quick showers and uses a dishwasher. That is why hot water design should be based on real usage, not just a simple rule of thumb.

Confidence Matters

At 11 Kings View, hot water was especially important because not everyone in the home was fully convinced about having a heat pump.

The customer’s wife was unsure at first. Like a lot of people, she had heard negative stories about heat pumps not working properly, or about homes running out of hot water.

So one thing was non-negotiable on this project: the system could not run out of hot water.

That meant the design had to give the household confidence. It was not enough for the system to look good on paper. It had to suit the way they actually lived, give them enough stored hot water, and still keep the system as efficient as possible.

This is why the customer conversation matters. Hot water is personal. If someone has lived with a boiler for years and is used to very hot water at the tap, the heat pump system needs to be designed and explained properly so they know what to expect.

Efficiency vs Quantity

With a heat pump, there is always a balance between efficiency and the amount of stored hot water available.

In simple terms, the smaller the volume of water being heated, the less energy is needed to heat it. A smaller cylinder will usually have lower standing losses than a much larger cylinder, and it avoids keeping unnecessary hot water stored.

Temperature matters too.

The lower the hot water temperature, the more efficiently the heat pump can heat it. Heating water to 45°C is generally easier for a heat pump than heating it to 55°C or 60°C.

But the system still has to work for the customer.

Some people are used to boiler systems where the hot water feels very hot at the tap. For those customers, 45°C may not feel hot enough, especially for washing up by hand. Other customers may use a dishwasher and mainly need hot water for showers, so a lower temperature may be completely fine.

The best design is not always the hottest water or the biggest cylinder. It is the right balance between comfort, efficiency, available space, and how the customer lives.

How Often Should the Cylinder Reheat?

Another important part of hot water design is the reheat strategy.

One option is to heat the cylinder once a day on a timed schedule. This can work well if the customer has cheap overnight electricity. The cylinder can be heated during the off-peak period, ready for the next day.

Another option is to let the cylinder reheat automatically when it drops below a set temperature. This is controlled using hysteresis.

For example, the cylinder could be set to 50°C with an 8°C hysteresis. That means the heat pump would not start another hot water cycle as soon as the cylinder drops to 49°C. It would wait until the cylinder temperature drops to around 42°C before reheating.

Viessmann ViCare App, Domestic Hot Water Controls

This helps stop the heat pump constantly switching on and off just to top up small amounts of hot water.

Again, the right answer depends on the customer. Some people want maximum efficiency and are happy with one timed heat-up. Others want the reassurance that the cylinder will reheat automatically when the temperature drops.

Cylinder Location Matters

Where the cylinder is positioned also affects the design.

Ideally, the cylinder would be inside the heated envelope of the home. This helps because any heat lost from the cylinder or pipework is still inside the property, rather than being lost into a garage, loft, or cold external space.

Shorter pipe runs can also help. If the cylinder is closer to bathrooms and kitchens, less heat is wasted in the pipework and hot water usually arrives quicker at the taps.

But in real homes, the ideal location is not always possible.

Sometimes the cylinder has to go in a garage, loft, cupboard, utility room, or another available space. The design has to balance efficiency, space, access, pipe routes, disruption, and what suits the customer.

At 11 Kings View, the cylinder location needed careful thought because the available internal space was limited.

The 11 Kings View Loft Cylinder Challenge

At 11 Kings View, the hot water design used two slimline cylinders located in the loft.

This was not just a case of putting cylinders wherever they would fit. Cylinders are heavy, especially when full of water, so the support arrangement had to be properly considered.

One of the biggest challenges was that there was no suitable load-supporting wall in the loft where the cylinders needed to go. That meant we could not simply rely on a standard wall-mounted arrangement or assume the existing loft structure was suitable.

A purpose-made bracket and support arrangement was designed and built so the cylinders could be safely positioned in the available space.

This part of the design mattered even more because running out of hot water was not an option. The hot water storage, cylinder position, pipe routes, weight, access, maintenance space, and customer usage all had to be considered properly.

It is a good example of why heat pump design often needs more thought than people expect. The heat pump outside is only one part of the system. The hot water side of the installation is just as important to how the customer experiences the system every day.

Built Around the Customer

Hot water is personal.

Some people want hotter water because that is what they are used to. Some people want maximum efficiency. Some want enough stored water for back-to-back showers. Some want the cylinder heated overnight on cheap electricity. Others want the cylinder to reheat whenever it drops below a certain temperature.

There is no single answer that works for every home.

A good hot water design should look at:

The number of people in the property
How often they shower
How long they shower for
Whether they use baths
Whether they wash up by hand or use a dishwasher
What hot water temperature they are comfortable with
Whether they have off-peak electricity
Where the cylinder can realistically go
How long the pipe runs will be
Whether the structure can safely support the cylinder location

At 11 Kings View, the final design was built around the property and the customer, not just a standard cylinder size.

That is what good heat pump design should do.