And How to Get Them Right
Heat pumps are getting more attention than ever in the UK, but they still divide opinion.
You might have heard people say:
“They don’t work.”
“They cost too much to run.”
“They don’t get the house warm.”
The truth is, heat pumps do work, but only when they are designed and installed properly.
Many poor installations gave heat pumps a bad name, not because the technology is bad, but because the basics were missed.
Boilers and Heat Pumps Are Not the Same
In many homes, a boiler can be bolted onto an old heating system and still get the house warm. Even if the system is not designed very well, the boiler can usually force enough high temperature water around the radiators to make it work.
A heat pump is different.
A heat pump works best at lower water temperatures, running steadily and efficiently in the background. It should not be treated like a gas boiler or installed as a straight swap without proper design.
This is where many heat pump problems start.
Why Some Heat Pumps Fail
Most heat pump problems are not caused by the heat pump itself.
They are usually caused by poor survey, poor design, or poor setup.
Common problems include:
- No proper heat loss calculation
- Guessing the heat pump size
- Radiators that are too small
- Pipework that is not suitable
- Poor control setup
- Weather compensation not set correctly
- The system cycling on and off too much
When these basics are missed, the heat pump may need to run at higher temperatures, which makes it less efficient.
The result can be a colder home, higher bills and an unhappy customer.
Why Room-by-Room Heat Loss Matters
A good heat pump installation starts with understanding the home.
That means working out how much heat each room needs on a cold day.
Every room is different. A living room, bedroom, bathroom and kitchen can all lose heat at different rates depending on their size, windows, walls, insulation and position in the property.
This is why a room-by-room heat loss calculation is so important.

It helps decide:
- What size heat pump is needed
- Whether the radiators are large enough
- Which rooms need radiator upgrades
- What flow temperature the system can run at
- How the system should be designed
Without this step, the installation is partly guesswork.
And heat pumps should not be guessed.
Why System Design Matters
A heat pump is not just an outdoor unit.
The whole heating system needs to work together.
That includes:
- The heat pump
- Radiators or underfloor heating
- Pipework
- Pumps
- Hot water cylinder
- Controls
- Flow temperatures
- Customer settings

If one part of the system is wrong, the heat pump may have to work harder than it should.
For example, if the radiators are too small, the system may need hotter water to heat the rooms. Hotter water means lower efficiency.
If the pipework is too restrictive, the heat pump may struggle to move enough water around the system.
Good design helps avoid these problems before the installation starts.
Weather Compensation: Simple but Important

Weather compensation sounds technical, but the idea is simple.
The heat pump changes the water temperature depending on how cold it is outside.
On a mild day, the radiators do not need to be as hot.
On a colder day, the system gradually increases the temperature to keep the home comfortable.
This helps the heat pump run smoothly and steadily, rather than constantly switching on and off.
A well-set-up heat pump should feel calm and consistent. The home stays comfortable, without big temperature swings.
Why Bigger Is Not Always Better
With boilers, people often think bigger is safer.
With heat pumps, oversizing can cause problems.
If a heat pump is too big for the property, it may switch on and off too often. This is called cycling.
Cycling can reduce efficiency, increase wear on the system and make performance worse.
The best heat pump is not always the biggest one.
It is the one that has been correctly sized for the property.
Getting Heat Pumps Right
When a heat pump is designed and installed properly, the results are very different.
A good system can provide comfortable heating, reliable hot water and excellent efficiency.
Well-designed heat pump systems can often deliver around 3.5 to 4 units of heat for every 1 unit of electricity used, depending on the property, design and operating conditions.
That level of performance only happens when the fundamentals are right.
At VAYU, the focus is on getting those fundamentals right from the start.
This includes:
- A detailed property survey
- Room-by-room heat loss calculations
- Radiator and pipework checks
- Careful heat pump sizing
- Correct system design
- Weather compensation setup
- Customer handover and controls
- Performance monitoring where required
Because with heat pumps, it is not about just making the system work.
It is about making it work properly.
The Takeaway
Heat pumps do work.
But they need to be designed differently from gas boilers.
A poor installation can lead to high bills, poor comfort and a bad experience.
A good installation starts with the survey, the heat loss calculation, the system design and the setup.
Get those right, and a heat pump can be comfortable, efficient and reliable.
At VAYU, we design heat pump systems around the home — not around guesswork.